Product Description

Rotating speed: ***0rpm/min Power: 3KW/4KW Voltage: **0V/**0V Lock(inner) range: 1/4"*2" Dies: *0sets Dies No.: *5,*9,*3,*6,,*1,*6,*1,*7,*5,*0 Withhold accuracy: 0.*1mm Max. opening: **4mm Opening extension: ±*0mm Buckling pressure: **0T Effcency: **0pieces/hour Systerm pressure: *1.5KPa Swept volume: 2.5/5L
The pipe pressing machine is a hydraulic device for crimping the pipe fitting assembly, which applies the shrinking force of the matched metal joint through the die of the crimping machine, and firmly presses the metal joint on the supporting high-pressure oil pipe or automobile for construction machinery. Brake pipe, oil pipe, air conditioning pipe, power pipe. The crimping machine is suitable for all kinds of mechanical high and low pressure oil pipes, gas pipes, water pipes, cable joints, automobile air conditioning pipes, automobile power steering pipes, oil pipes, gasoline fuel supply pipes, as well as the buckles of construction parts and daily hot water pipes. Vehicles, engineering machinery, hydraulic machinery, welding and cutting equipment and other industries.

According to the use function, it can be divided into hydraulic high pressure pipe press machine, brake pipe press machine, air conditioning pipe press machine, power pipe press machine, etc., according to the mechanical structure can be divided into straight tube press machine, double column pressure Pipe machine, open type pipe pressing machine, C type pipe pressing machine, according to the control mode can be divided into electromechanical pipe pressing machine, PLC type pipe pressing machine, numerical control type tube pressing machine.

2 installation and debugging
The tube press is suitable for handling by forklift and is forced by the bottom of the tube press. The tube press is strictly prohibited from being inverted. Specially added to raise the hand, so that users without forklifts can move at will. It is strictly forbidden to lift the pipe head and the motor and electrical box parts.

1. Installation: The crimping machine and the pressure tube machine should be placed horizontally on a stable foundation and grounded.

2. Fill the oil: Open the fuel tank cap and add *6 hydraulic oil to the oil tank 2/3 position.

3. Power-on: Connect the power cable to the power supply specified by the buckler, start the motor to observe the steering, and the motor steering should be consistent with the direction marked by the motor. If the motor is not in the same direction as the marked direction, please change the position of the two live lines. Micrometer: used to adjust the amount of shrinkage of the crimping hose. Press 1mm counterclockwise for half a week and 1mm for half a week clockwise.

4. Pressure adjustment: The maximum pressure of the crimping machine and the tube press system is *1.5Mpa, which is adjusted by the relief valve. The pressure is increased clockwise and the pressure is reduced counterclockwise (the factory has been adjusted and can be adjusted if necessary) . Mold opening speed adjustment: the speed of the mold opening speed is controlled by the diverter valve, clockwise adjustment, the opening speed is increased, counterclockwise adjustment, the opening speed is slowed, but the opening speed is too fast, the noise will increase, the most The good value is not more than *0Mpa (it has been adjusted at the factory and can be adjusted if necessary).

3 use method editing
1. Before starting the machine, press the pressure machine and the pressure tube machine to add *0# hydraulic oil *0kg (preferably the original brand original oil).

2. Connect the power supply. If you are using a three-phase motor, be careful not to reverse it (top view: the motor fan is clockwise for positive rotation).

3. After the above process is completed, the test can be started.

4. Use of crimping machine and pressure tube machine positioner: press 1mm per revolution for one week, 0.*1mm for each positive rotation, and so on, the same specification hose, joint, the first metal joint can reach the required pressure There is no need to move the positioner again, and the specification has been pressed all the time. The result is that the compression data is completely consistent. When you try to complete the first oil pipe, you have already learned, and the rest is gradually skilled.